SẢN PHẨM KHUYẾN MÃI

Soldering related equipment and materials HAKKO 374

Mã sản phẩm:

Giá: Liên hệ

Kho hàng: Còn hàng

Hotline: 0968.485.838

Automated solder feeding and solder/flux splash prevention
Minimize solder and flux splash
As shown below, when solder is cut with a V-groove it enables the release of gas pressure generated by the flux, thereby suppressing splash. However, because the V-groove exposes the flux to outside air the solder cannot be stored for a long period of time. 
When using solder with the HAKKO 374, you can groove the solder that you require. 
Minimize solder and flux splash 

HAKKO Document Portal

You can browse and download "Instruction Manuals" and "MSDS (SDS)" freely.
Even "Engineering Documents"are available once you complete user registration.

Inquiry form

Control work easily
 
· Automatic solder feeding with a switch on the grip.
· You can keep your hands clean.
· No need to draw out solder wire.
Set feed time and speed
Solder return function 
Use feeder pen for easy control of solder feed


 

 Supports both one- and two-handed soldering
  · Automates the solder feed process
    Solder supplied using a feeder pen.

 

Example setup  
Example setup  
   
  · One-handed soldering also possible
    Attaches to soldering iron and supplies solder automatically.
 

Soldering irons supporting one-handed soldering

 

Example setup  
Example setup  


 

 A feeder pen (pen-shaped feeding guide) can also be used.
Using a feeder pen enables you to work with both hands
• Automatic solder feeding with a switch on the grip.
• You can keep your hands clean.
• No need to draw out solder wire.


 

 Solder splash test
Solder Ø0.8 x 250 mm (Sn 60%)
Feeding Condition Solder is fed for 5 seconds at speed of 10 mm/sec in 5 cycles.
Tip Temperature 400ºC
Solder ball splash test results / It is possible to reduce solder splash by cutting a groove along the length of the solder
* The effect of splash prevention may differ depending on the work condition.

 

Number of splashes of flux/solder
Solder without a V-groove 81
Solder with a V-groove (cut by 374) 0

Usage/Applications

ø1.6 Lead-free solder is NOT available for use.
Combination  
   
· Soldering with Feeder pen
Soldering with Feeder pen
· Soldering for one-handed manipulation
Setting Sample of Self Feeder HAKKO 373
  Applicable Soldering Iron

HAKKO FM2030

HAKKO FX838

HAKKO FX888D

HAKKO FX888

HAKKO FM-2030 HAKKO FX-888 HAKKO FX-888D HAKKO FX-888
*Discontinued

HAKKO 
FM2027/2028

HAKKO 912

HAKKO 928

HAKKO 931

HAKKO 2027 2028 HAKKO 912
*Discontinued
(Available only when attaching Long nipple)
Soldering Station HAKKO 937
(Not available for HAKKO 900S)
Soldering Station HAKKO 931
*Discontinued

HAKKO 936

HAKKO 937

HAKKO 958/959

HAKKO DASH
(N452/N453/N454)

Soldering Station HAKKO 936
*Discontinued
(Not available for HAKKO 900S)
Soldering Station HAKKO 937
*Discontinued
(Not available for HAKKO 900S)
Soldering Gun HAKKO 958, 959
(A station is needed separately)
Soldering Iron HAKKO DASH

HAKKO MACH-I

     
Soldering Iron HAKKO MACH-I
*Discontinued
     

 

Hints On Use
1. I want to use the HAKKO 374 for a different solder diameter.
Change all of the driving/following pulley assembly, supply nozzle, guide pipe assembly, and tube unit.
2.

I want to change the soldering iron used with the HAKKO 373/374.
Change the iron holder, guide pipe assembly, and tube unit if they are not compatible with the soldering iron to be used.

 

 

hikaru What advantages does the rewind function have?
If the solder remains near the tip after soldering, the heat from the tip will cause it to melt, which in turn causes the flux on the end of the solder to splash or results in or excessive solder feed due to solder beading. The rewind function is designed to help avoid these issues. 
This mechanism ensures smooth, trouble-free soldering work. The length of solder that is rewound can be adjusted by inserting a flat-bladed precision screwdriver into the adjustment hole on the side of the soldering station.
set